RIM CYLINDER LENGTH

RELATED FAQS

Question
Answer
A 1 1/4" mortise cylinder with straight cam (similar to the Schlage B502-191) or a 1 1/2" mortise cylinder with straight cam using supplied spacer collar. Cylinder length does not chan...
The existing 373L control was modified and re-named as 379L to allow us to use the 55 rim device on an ADA door opening.  The 379L control is our 373L with different hex st...
Key-in-lever tailpieces differ in length depending on the lock series, function, and design.  Click here to identify the tailpiece and length.  NOTE: Modular cylinders use...
The Sargent cams listed below work for all applications except 16 inside and 50 outside.  The equivalent Sargent cam is the 13-0660. Use the B520-736 for modular cylinder lengths of 1 1/8",...
Click here for a list of available Schlage cams comparable to the Sargent 13-0660.
The Schlage rim cylinder lengths are given below and were measured from the face of the cylinder to the back of the tailpiece.  Because of allowable tolerances for each part the average length is l...
 The tailpiece of the rim cylinder can be inserted into the Von Duprin 98/99 rim device either vertical or horizontal.
Order the device as 88 NL less trim. The cylinder will be mounted to the face of the door. Use templates 10156 and 40015.
The 2670 Guard X uses a standard rim cylinder for either push side or pull side.  The rim cylinder can be installed to the outside of the opening with an offset pull to operate the 2670 Guard X d...
The 98/99 rim device can be converted to double cylinder 98-2 or 99-2. Double cylinder features an inside key cylinder which locks or unlocks the outside trim (Classroom Function) and an outside c...
The B220-001 is an FSIC rim tailpiece and driver.
A 1-1/8 through 1-1/2" mortise cylinder with straight cam per Step 4 of 512NL Instructions.
The Schlage small format interchangeable core rim cylinders 80-329, 80-159, 80-116, and 08-129 can accept 6 pin and 7 pin small format cores.
Rim cylinder housing only for FSIC is part number 20-079.
Rim cylinder housing only for SFIC is part number 80-129.
To add a cylinder to the 98/99-EO rim device order a 110NL-MD for metal door or 110NL-WD for wood door with a standard rim cylinder and prep the door per template.
Standard Schlage rim cylinders will fit a total thickness of door and projecting trim of 3 inches, this includes a minimum of 3/8" of engagement of the tailpiece into the exit device.  See ima...
For total thickness measurements larger than 3 inches see the special cylinder offerings in Pricebook.  Specify the part number and include the total thickness.  We do not offer the ...
The Schlage SFIC rim cylinder driver is part number B520-365, shown below.     Figure 1: SFIC Rim Cylinder Housing
The rim cylinder with thumbturn, XB11-979 (Figure 1) was designed to be installed on the inside head of the Von Duprin 98/99–2 double cylinder exit devices, see Figure 1. The rim cylinder with...
See descriptions for the 09-992 thru 09-997 parts kits for modular mortise cylinders.  The 09-998 is a kit for a rim cylinder.      
B502-899 is the tailpiece for both the SFIC and standard rim cylinders.
The 98/99 rim device can be converted to double cylinder 98-2 or 99-2. Double cylinder features an inside key cylinder which locks or unlocks the outside trim (Classroom Function) and an outside...
No, the 98/99 series mortise exit device should be ordered as NL less trim. IE, 9875NL-L/TRIM. NL-OP suffix is normally used with the 98/99 series rim, surface and concealed vertical rod devices wh...
The following list of cylinders were not affected by the change to modular cylinder:    09-900, 09-904, 09-905, 09-907 mortise cylinder turnsSmall format interchangeab...
Part numbers for Schlage and Falcon cylinders for Von Duprin devices are listed below. (KIL = Key In Lock) SCHLAGE   Mortise Rim KIL ...
FALCON   Mortise Rim KIL Conventional 986 x #4 cam 951 A23165-02 Small Format Housing C987...
If unclear whether mortise, rim, or key-in-lever is needed, reference links below to determine what cylinder type is needed.  In order to determine cylinder type needed,  you must first k...
There is not enough room for both options as the dogging mechanism in a standard cylinder dogging and the electronics for the EL or QEL options are both located at the end of the base plate. For 9...
Inside cylinder locks and unlocks the outside trim, such as thumb piece, knob or lever.  Outside cylinder functions as an NL when inside cylinder locks the outside trim.Double cylinder fe...
You would have to order the device as 88NL less trim, the device will be shipped as an 88EO.  The EO device has an NL cam to accept a rim cylinder tailpiece. 
You will need a 1790NL/HB cylinder assembly (part number CYLASY.1151) and a rim cylinder.
The 38-070 is a dummy mortise cylinder available in 1 1/8", 1 1/4", 1 3/8", 1 1/2" lengths.  The cylinder has an embossed faceplate to look like a standard cylinder but no keyway.
The 38-070 is not available in stainless finishes; 629 and 630.
A modular cylinder's length is determined by 4 basic parts; a cam screw, cam, plug extension, and a back housing.  Most of these parts are used in more than one cylinder length and...
1 1/8" mortise cylinders fit the 650 series keyswitch.  The 650 series keyswitch when ordered with the cylinder, will come complete with the correct cylinder, cam, and any required blocki...
If blocking rings (PN 36-079) are needed, specify dimensions when ordering. See below for blocking ring (PN 36-079) dimensions.  Blocking Ring  Specify Dimension  1//8" ...
Typically for a 1-3/4" door you would use a 1-1/4" cylinder.  Use the Table in the Pricebook for a reference:  
Chexit devices shipped after 8-24-2015 with motor driven: The Chexit device will use a 1 1/4" mortise cylinder with straight cam. Schlage cylinder 20-001-114 recommended. CAUTION: The length of t...
Chexit devices shipped prior to 8-24-2015:The CX device will need a 1 1/4" mortise cylinder with a straight cam per page 2 of the installation instructions. A 996L-M for a 1 3/4...
There are different mortise cylinder length options depending on the cylinder type. Below is a list of available options for conventional, FSIC, and SFIC cylinders, as well as the convent...
Von Duprin offers two options:The CDSI/HDSI Dogging Indicator provides an at-a-glance verification of the status of the door from inside of the room. Visible “LOCKED” and “UNLOCKED” indicators show...
SD is Special cylinder dogging in the center case of 98/99 rim and vertical rod non fire rated devices and is available with standard, EL, QEL, CX and ALK.
This is possible: For metal doors prep door according to the 24R/V NL-OP Template or the 25R/V NL-OP Template and for wood doors use 24R/V NL-OP Wood Template or 25R/V...
Both cylinders are standard non-ic rim cylinder. 20-022 has a horizontal tailpiece 20-021 has a vertical tailpiece
Modular cylinder was launched July 26, 2010 and replaced the standard key-in-lever, mortise, and rim cylinders.     For a list of cylinders not affected by the modular cylinder design change cli...
This product was available until 2001 when it was discontinued. Part Number Description XB09-728 Entrapment mortise cylinder, P keyway XB09-834 Entrapment rim cylinder, P keyway ...
Schlage offers a comparable cam to the Yale 2160 and it will operate any Yale lock that utilizes the Yale 2160 cam.     Schlage Cams for Yale 2160  Part Number  Description  B520-7...
There have been a few reported cases of the torx cam screw loosening on modular designs shipped prior to April 16th 2013.   History of cam screw changes: Standard screw shipped July 27t...
Schlage now offers modular style cams to operate the Falcon MA locks.  The following part numbers are cams for all MA locks (except the MA381): L583-638 for 1-1/8", 1-3/8", 1-5/8" length cylin...
Price Book 72A List Price $8.10
The Schlage L-Series uses a clover leaf cam with the exception of the L9060 outside cylinder which uses a straight cam. The cam part number will depend on the type of mortise cylinder, keyway (for ...
These cylinders are designed with a microswitch attached to the back of the cylinder. The switch is operated by a cam when the key is rotated.   To order: XB09-195 Mort...
The XB09-195, XB09-795, and XQ11-804 are basically modified mortise cylinders. The overall length of the mortise cylinder switch is approximately 1-9/16" (1.563"). The diameter of the cylinder face...
The current 812L trim will replace the older 182L trim. Due to the thicker escutcheon plate of the 812L trim a 1 1/2" mortise cylinder with straight cam for mortise devices or a longer rim cylinde...
Double cylinders are only available on Von Duprin 98/99 Rim and 98/9975 Mortise devices.