Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ Ad coin cell part number ”

RELATED FAQS

Question
Answer
Why do AD Series offline locks still give a Low Coin Cell indication after I install a new coin cell?
Coin cell replacement is not immediately registered by the AD200/250 firmware.
Performing a processor reset (pressing and releasing S1 on the Main PCB Assembly) will register the new coin cell.
Cycling lock power (i.e., disconnecting and reconnecting the "AA" battery pack) will register the new coin cell.
The coin cell part number is CR2025 - 3 volt lithium - available at most battery or electronics stores.
I replaced the CT5000 coin cell, but I still get a Low Battery indication.
Coin cell replacement is not immediately registered by the CT5000 firmware.
Performing a processor reset (pressing and releasing the RESET button) will register the new coin cell.
Coin Cell part number is CR2025 - 3Volt Lithium - available at most any battery store.
What type of coin cell is used in the AD / CO Lock?
The coin cell for the AD and CO family of electronic lock products is a 3vdc lithium. CR2025 is the specified part number.
What is the low battery threshold for the AD and CO Locks?
Information on low battery threshold and nuisance delay is noted below: New firmware now has improved levels. - These are approximate values/levels which change with measurement meters and measure...
AD400/AD200/AD250 After ADFwPkg 2.17.0 - June 2011 4 Battery Holder New batteries = 6.2 VDC Low battery threshold is 4.7 VDC for SM & MT - and 3.7 VDC for MAG and PROX (USB stops working at 4...
    AD400/AD200/AD250 After ADFwPkg 2.17.0 - June 2011 8 Battery Holder New batteries = 12.4 VDC Low battery threshold is 7.2 VDC Critical battery threshold is 6.9 VDC Coin cell = new/...
CO2004 Battery Holder (ONLY) New batteries = 6.2 VDC Low battery threshold is 4.2 VDC Critical battery threshold is 3.9 VDC Coin cell = new/full is 3.0 VDC, low is 2.8 VDC
CO2504 Battery Holder (ONLY) New batteries = 6.2 VDC Low battery threshold is 4.2 VDC Critical battery threshold is 3.9 VDC Coin cell = new/full is 3.0 VDC, low is 2.8 VDC
  CO200 & CO250 Disable coin cell Nuisance delay and blink, With CO.A.7 and SUS 4.10.2 or newer for CO200 and CO250, you can use the SUS/HHD, under Lock Properties, Edit, to de-select, DISABLE, t...
Can the low coin cell Nuisance delay be Disabled on a CO200?
The coin cell Nuisance Delay on CO200 and CO250 can be temporarily disabled using the Schlage Utility Software.
Once disabled via the SUS application, the CO lock will no longer delay the access for valid credentials.
If your CO lock began indicating a low coin cell (Nuisance Delay) after a door file has been downloaded, the coin cell is low and should be replaced. (CR2032)The coin cell Nuisance Delay will be "A...
The coin cell Nuisance Delay settings in the SUS application is not available until such time that a Door file is successfully downloaded to the lockset.
The coin cell is ignored when the lock sets are used with Manual Programming ONLY or while in Construction mode.
What is the part number for the twisted tailpiece for AD/CO exit device trim locks?
The part number for the AD or CO twisted tailpiece kit is: 46929303 Tailpiece Kit - (for Exterior Escutcheon -993 into Exit Device, i.e. Von Duprin 98 or 99) Exit Trim 46929303 Includes the...