Grade 2 locks are tested and certified to be in compliance with the following ANSI/BHMA Standards:
Cylindrical, Bored and Preassembled Locks & Latches
400,000 Certified Cycles
ANSI...
The old D-Series Lever used a standard lever insert similar to the pre-2002 AL-Series standard lever insert. The old D Lever insert was smaller than the AL and the two were not comp...
There is no conversion kit to add EL or ED to an existing 1690 or 1790 series device.
All of the components are built into the device, since the device does not have a separate base...
The AL-Series has four distinguishable parts that can help in lock identification.
1. The AL-Series will have a castle nut holding the chassis on the ...
The easiest method to obtain an AL lock for a 2" door is to specify a 2" thick door when ordering.
Part required by function:2 each A700-043 driver & A700-034** lever insert in addition to the chassis parts below:AL10S – 2 hubs A700-028AL25D – 2 hubs 1 A700-028 (inside), 1 A700-030 (outside)...
Order the M204-198 thru-bolt jig, see Figure 1.
Figure 1: M204-198 thru bolt jig
The 40-080 was the old Schlage jig. The 030736-000-70 was the old Falcon jig. When the jig changed to...
AL-Series and discontinued D Lever-Series locks use castle nuts to hold the chassis to the spring cages and to keep the chassis positioned in the door. This causes confusion at times when the lock ...
- AD Series and CO series products require that the Night Latch (NL) screw is installed in the exit device. Be sure this screw is installed- Exit hardware and strike must be properly mounted ...
If your Von Duprin EL (solenoid) device pulls and releases quickly instead of holding the latch retracted, please check all of the items below.In most cases, one or more of these solutions will r...
You must have the Von Duprin NL Cylinder plate part number 967484-89 to convert the 370 series controls from classroom function to night latch function. If new installation, use the NL cylinde...
In 2002 the Schlage AL-Series underwent a design change that affected the spring cage, driver, and plastic insert. Spring cage and driver replacements for AL locks manufactured before this design ...
39-030 can be used on the A, AL, B250, B500, B600, D, ND, S products.
This kit adapts a square corner latch and a 2 3/4" high square corner strike to 1/2" rabbeted door and frame preparation.
How to: What are the steps to adjust a door closer?
Facts: All LCN and FALCON door closers will have 3 regulating valves and a spring adjustment. All cl...
The new AL FSIC driver part number is A700-052.
This driver snaps onto the back of the core similar to the ND, as opposed to it being assembled into the lock chassis with a retaining ring.
Th...
The Schlage AL-Series SFIC locks require one (1) small format spacer (D500-000) for 7-pin cores and two (2) small format spacers for 6-pin cores. When these spacers are not ins...
There was a design change in 2001 for the driver and lever insert on the AL for SFIC products. Changing the driver and/or lever insert on locks manufactured prior to 2001 will requi...
The SFIC lever insert part number prior to 2001 was the A700-022.
The indicator on a cylindrical hotel lock is a small pin that projects outward from the face of the cylinder plug (Figure 1) when the inside push button is depressed. When this pin is ...
When the new PS900 series power supplies were created we did not pursue a version of these option boards. Need to discuss the specific hardware they are using and requirements to determine the app...
Refer to table 1 for the list of Schlage AL-Series cylinders.
AL-Series Cylinder Reference Table
Function
Cylinder Mechanism
Complete Cylinder
Non-Hotel Functions
...
The standard door range for an AL lock is 1 3/8" to 1 7/8". Using the supplied instruction sheet, align the springcage post to desired door thickness by adjusting the outside castle nut.
See inst...
Cylindrical Locks: a bored lockset whose latch or bolt locking mechanism is contained in the portion installed through the cross-bore
Medium, high to extra heavy duty
Commercial, mul...
Schlage offers the 10-042 Electric strike, 1 1/4" x 4 7/8", 606 and 626 finish only.
Related solution: What are the current and voltage requirements of ...
Only the Schlage D-knob and ND products are available with an extra long backset. The part number for backsets over 5"-42" is XC03-069, this part will ship as an extension link to b...
The new latch, introduced mid-June 2013, will NOT fit into the previous T lock chassis. Customer are encouraged to order a new Falcon T lock. If needed, customers can replace the older ...
A and AL product: Must use the 2 3/8" backset with the 41-005 extension link
D Knob and ND product: Must use the 2 3/4" backset with the 43-005 extension link
A lock is any device which prevents access or use by requiring special knowledge or equipment. Mechanical locks are mechanical devices which secure an opening by keeping a door closed until a rel...
The 98/99 rim and vertical rod exit devices are shipped with NL drive screw to function as a Night Latch.
To convert the device to Class Room, remove the NL Drive Screw on 98/99 center case ass...
Grade 1 locks are tested and certified to be in compliance with the following ANSI/BHMA Standards:
Cylindrical, Bored and Preassembled Locks & Latches
8...