Cylindrical Locks: a bored lockset whose latch or bolt locking mechanism is contained in the portion installed through the cross-bore
Medium, high to extra heavy duty
Commercial, multi-family a...
You should use the LX switch with the Von Duprin surface vertical rod exit device because the rods are exposed and are vulnerable to attack. IE, the top rod can be grasped and forced down to retrac...
Deadbolt Locks (Deadlocks): a lock with a bolt which requires a deliberate action to extend and which resists end pressure in the unlocking direction when fully extended
Medium, high to extra he...
The 2670 Guard X uses a standard rim cylinder for either push side or pull side.
The rim cylinder can be installed to the outside of the opening with an offset pull to operate the 2670 Guard X d...
The difference between the Brass version 482B and the Aluminum version 482A is the size and design as well as the base material and available accessories. The Brass version 482B comes w...
Exit devices are not designed for exterior application.
If used in an exterior applications then a powder coated finish on the 33/35 and 98/99 series are recommended for exterior applications.
...
The LCN Safety (Finger) Guard was a heavy duty vinyl product that covered the opening between the door and frame, where most hand injuries occur.
The LCN 750 Safety (Finger) Guard was the pul...
Von Duprin does not offer any lever trim or pulls that through bolt to the Guard X device.
Ives has the 8102-6 and 8105-6 pulls that can be lined up with the mounting screws of the exit device b...
Replacing the battery on the 2670 should not cause the unit stop working. Make sure the spring that provides tension on the plastic finger is not bent out. The spring should be at a 90 degrees...
The Von Duprin Guard-X exit device is not fire rated because the deadbolt is not spring loaded. Therefore, there would be no positive latching as required on a fire rated opening.
Mortise Locks: a lockset where the case is designed to fit in a mortise in the edge of a door
Medium, high to extra heavy duty
Commercial, multi-family and institutional applications
Pros - ...
The Y latches listed below are adjustable to fit either a 2 3/8" or 2 3/4" backset.
LATCHES WITH LOCKS
Description
Backset
Specify
Square corner, 1-1/8" x 2-1/4", standard
2...
The latches for the Y and F lock are not interchangeable as the hole sizes are different. Substituting any latch voids your UL and product warranty.
Catalog information for Ives Edge Guards is currently being developed. The order form with part numbers is available. Ives Edge Guard Order FormIves Edge Guard BrochureIves Edge Gua...
Interconnected Locks: a lockset whose trim provides a means of simultaneous retraction of two or more bolts which may also be operated independently
Medium duty
Commercial, government or multi-...
DISCONTINUED: The Falcon T lock had a reinforcement kit for a 1 3/4" thick hollow metal door that prevents lateral movement of the latch. It is a piece of hard foam shaped like a doughnut...
The 98/99 rim and vertical rod exit devices are shipped with NL drive screw to function as a Night Latch.
To convert the device to Class Room, remove the NL Drive Screw on 98/99 center case ass...
The Schlage full size interchangeable core (FSIC) prepped B560F, B561F, and B563F deadbolts all require a UL fire cup (R) in order to be UL listed. This fire cup is s...
With a mullion: Use the standard strike 267
With no mullion and inactive leaf being held closed with flush or surface bolts: Use the 2609 double door strike
Following parts are required to add the bottom rod and latch to the 98/9927-LBR/LBR-F device.
Bottom Rod: 050515 for 9827 and 050514 for 9927 (specify finish)
Bottom Latch Assembly:...
Yes, as an option, Steelcraft doors are available with factory prepared for the 98/9949 Concealed Vertical Cable Exit Device.
L, B, CE, T and CE-Series doors are available factory prepared
Door...
The RU series from Falcon is a pre-assembled unit lock designed to retrofit existing unit locks manufactured by Falcon, Corbin Russwin and Yale. It exceeds ANSI Grade 1 specifications and is ...
Yes, you could use the RG27 on top rod but we recommend RGO.
The RG27 is a latch and rod guard and the RGO is a rod guard only. A latch guard is not needed for top latch, only for bottom latch.
The door handing determines the finish of the latch and strike.
Left reverse and right reverse doors default to outside trim
Left and right hand doors default to inside trim
If lever an...
The Ives 482 does not come with a rub plate. The brass 482 Door guard (also called 482B) comes with an edge guard or plate that is applied with adhesive to protect the edge of the door.T...
Panic Hardware and Fire Exit Hardware are two different types of exit devices, and the proper selection is determined by code requirements.
Panic Hardware is an exit device which is tested for u...
The most obvious difference (in the device) is the lack of mechanical dogging on a Fire Rated Device. There are some internal parts that may be different and the method it is secured to the d...