Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ cam for Corbin cylinder ”

RELATED FAQS

Question
Answer
Is there a cam for a Schlage IC cylinder to operate a Falcon MA lock?
The B520-698 cam was designed for a Schlage IC mortise cylinder (see Figure 1) to operate a Falcon MA lock, all functions except the MA381.  There is no Schlage cylinder option ...
What is the standard Falcon cam?
Unless otherwise specified on an order, the cam supplied on Falcon mortise cylinders will be the following: Non-IC mortise cylinder is the 5622-STD. IC mortise cylinder is the 5622-IC. Related...
Cams for other applications may be specified with no additional charge, see pricebook.
Which conventional cylinder cam is used with an Adams Rite MS series lock?
L583-446; Schlage Adams Rite MS modular cam used on 1 1/8", 1 3/8" and 1 5/8" cylinders    L583-447; Schlage Adams Rite MS modular cam used on 1 1/4", 1 1/2" and 1 3/4" cylinders  B502-944; Sch...
What mortise cylinder cam do I use on a Falcon MA lock?
The Falcon MA-Series requires a different cam for keyed functions than its predecessor the Falcon M-Series.
 
 
What mortise cylinder cam is needed for KR4023?
The KR4023 mullion requires a 1-1/4" mortise cylinder with straight cam. This is stated in box 7 on the first page of the KR4023 mullion instructions.
What is the correct Schlage cam # for 718C for a concealed vertical rod device?
Devices built After 2/28/2011: Use a 1 1/8" - 1 1/4" mortise cylinder with straight narrow cam. (Cam profile same as the Schlage B520-731, see table below for part numbers) Devices built Befo...
 Modular 1-1/8"  Modular 1-1/4"  SFIC and FSIC  Non-Modular Non-IC Conventional  Non-Modular Non-IC Everest Primus  B520-730  B520-731  B520-2...
Does the cylinder cam get inverted on the SD option for the Von Duprin 99 exit device?
 A 1 1/4" cylinder with straight cam is required for the Von Duprin SD (Special Dogging) exit device option.
The cylinder cam must be inverted with the SD option to work properly.
What cylinder is required to for the Chexit device?
Chexit devices shipped after 8-24-2015 with motor driven: The Chexit device will use a 1 1/4" mortise cylinder with straight cam. Schlage cylinder 20-001-114 recommended. CAUTION: The length of t...
Chexit devices shipped prior to 8-24-2015:The CX device will need a 1 1/4" mortise cylinder with a straight cam per page 2 of the installation instructions. A 996L-M for a 1 3/4...
Can the modular cams be used on the older cylinders?
The cams for modular cylinders are unique and are not compatible with any non-modular mortise cylinders, Schlage or any competitors.
Does the Von Duprin CD kit include the machined cover plate for the cylinder?
The Von Duprin CD kit comes with the cover plate machined to accept the cylinder dogging mortise cylinder.1 1/4" mortise cylinder with an inverted straight cam is required for CD option on Von Dupr...
How do I change my modular cylinder length?
A modular cylinder's length is determined by 4 basic parts; a cam screw, cam, plug extension, and a back housing.  Most of these parts are used in more than one cylinder length and...
What is the Falcon cam designation for use on 25 series trims?
For standard (non-IC) cylinders, use the Falcon #4 straight cam For IC cylinders, use the Falcon #5 cam 
What cylinder do I use on a Von Duprin Keyed Removable Mullion?
Von Duprin KR (key removable) mullions requires a 1-1/8" or 1-1/4" mortise cylinder with the standard straight cam, the cam is not inverted. Please see chart below for part numbers. 
instructions
What Falcon cam is needed for a C987 cylinder for a 24/25-C device?
The Falcon C987 cylinder can be ordered with the #27 cam as it has a similar profile to the Schlage B520-731 cam for trims after 2/28/2011.
What cam to use for a modular cylinder in Sargent mortise lock?
The Sargent cams listed below work for all applications except 16 inside and 50 outside.  The equivalent Sargent cam is the 13-0660. Use the B520-736 for modular cylinder lengths of 1 1/8",...
Does the cam have to be inverted for cylinder dogging on the falcon 25?
The cam is not inverted on the mortise cylinder for the CD option.
Cam screw loosening and falling off on modular cylinders.
There have been a few reported cases of the torx cam screw loosening on modular designs shipped prior to April 16th 2013.   History of cam screw changes: Standard screw shipped July 27t...