Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ door closer mounting ”

RELATED FAQS

Question
Answer
How do you mount an LCN door closer on an arched or radius door?
What are the dimensions of the SC70 footprint
The measurements from center line to centerline of the mounting holes are 2-3/8"  x  6-3/4".
Does the old style 4030 have the same templating as the new style 4031?
The old 4030 series was: Handed Mounted regular arm hinge side. Had sized springs, were not adjustable. The 4033 is an obsolete closer.  If required, handing can be verified by looking at ...
Can I use a Glynn Johnson 410 with a 4040 regular (pull side) mount?
ST-1630 is required when mounting a 4041 or 4040XP door closer regular (pull/hinge) side with a concealed GJ100 or GJ410 series over head stop.
Can a 4010 be mounted with swing clear hinges?
Locate closer and arm from the centerline of the swing clear hinge pin.
What is the minimum top rail needed for the 4111 EDA/HEDA?
The minimum top rail required to mount a 4110 closer is 5-1/8" measured from the stop of the frame. If the top rail is less than 5-1/8" the 4110-18 drop plate is required.
What side of the door is the 4040SE mounted?
The 4040SE is non handed and can be mounted on the push or pull side of the door.
What special template (ST) is used with a 4110 closer and GJ90 series?
ST-2730 is used with a 4110 closer and GJ90 series (up to size 4).  ST-2730 includes a special template and special arm with a -62G shoe and bent forearm. If a drop plate is required, a 4010-18 d...
What is the narrowest door a 4010 can be mounted on?
When templated for 140° the 4010 will fit on a 16-1/2" door leaf MINIMUM.
What is a 62A shoe used for?
The 62A shoe is used when it is necessary to install the door closer (lower) down on the door so that it will operate under accessories such as overhead stops, coordinators, etc.
What are Overhead Concealed door closer?
Overhead Concealed door closers are used to provide a more aesthetic look to the opening.  Concealed in either the frame or the door Offer the ability to be adjusted to maintain control o...
What regular arm closers mounted on the pullside can be held at 180 degrees?
The 1260, 1460, and 4030 regular arm closers on the pullside will allow 180° door opening and can be held open at 180°, frame and trim permitting.
What is the difference between an LCN CUSH arm, and an LCN EDA arm?
EDA ARM - The EDA arm is a heavy duty parallel arm mount.  The degree of door opening is determined by the template used for mounting. EDA arm closers can only be mounted as a Push Side parallel ar...
Can I mount an LCN Cush closer with an GJ overhead stop?
It would be unnecessary to use the CNS/Cush arm and the Glynn Johnson overhead devices in the same application, both mechanisms stop the door.
What are Hold Open Closers & Magnets?
Hold Open Closers & Magnets (Fire/Life safety products) provide a wide range of solutions.  Single or multi-point hold open closers Utilize an electromechanical closer. Hold the door o...
Can a pull side mounted 1460 open 180°
A 1460 Pull Side can be mounted standard template for 180°, frame and trim permitting.
A 4030 Pull Side can be mounted standard template for 180°, frame and trim permitting. 
A 1260 Pull Side can be mounted standard template for 180°, frame and trim permitting.
What is a surface mounted door closer?
Surface Mounted door closers are the most durable and common type of door closer. Mounted to the surface of the door or frame Can be configured (through installation or arm type) to meet a...
What would cause my door closer to try and open the door instead of closing it?
For a door closer that tries to open the door instead of closing it:The closer body could be mounted backwards on the door - check instructions for proper closer orientation.It could be the wrong h...