This option is not available as there is no NL cam to directly drive the rods and using a key to lift the heavy stainless, brass or bronze rods would damage the key.
The Falcon 1390 exit device is discontinued and parts are no longer available from the factory.
New England Door Closer may still have some older kits and can be contact...
Factory finished painted doors are available from Steelcraft. Frames "are not available" factory finished from the factory.
Doors are offered in variety of standard colors or can be fini...
Key-in-lever tailpieces differ in length depending on the lock series, function, and design. Click here to identify the tailpiece and length.
NOTE: Modular ...
When installing the arm; the gearbox shaft and door must be at the (+90°) full open position. The following step are used to install the Sr. Swing (REG) push arm.
Install t...
Use #18 gauge wire up to 200 feet maximum distance from PS900 x 900-2Q power supply to the QEL exit device. The new QEL+ no longer requires the 900-2Q board but still needs a different option board...
Product shipped on or after Feb. 8th, 2016
The "3034" and "3034H" are internal part designation that LCN uses to specify regular (3034) and hold open ...
On Feb 8th, 2016 - LCN launched the redesign of the Hold open clip which changed multiple components of our Track style closers, including the roller, track, hold open clip, and bumper.
Beginning with Firmware Packages ADFwPkg 2.16.3 and COFwPkg 1.20.0 the PIN length can be manually changed for AD200 and CO200 locks as follows:
1. Press {programming code (default is 97531)} then ...
This configuration is not possible as the anti-pick plate of a "DL" or "F" device center case interferes with the LM/DM switch mounted also on the center case.
The following items may cause the exit devices top latch from being held in the retracted position.
1. The top or bottom rods are out of adjustment.
2. The top latch hold back...
Following exit devices 2227/F, 33/3527A/F, 33/3547A/48A/F, 98/9927/F and 98/9947/48/F have similar rod adjustment procedures.
All top latches control the bottom latch assemblies. When do...
The spring in the hinge case or end case assembly lifts the crossbar and both lever arms. If broken, the crossbar and lever arms will drop down. The weight of the crossbar and levers will automati...
The new 33A/35A center case will not work with the old 33/35 series exit devices.
It is never intended to use parts to convert a device from one Series to another Series as this w...
To convert the Von Duprin 98/99 Rim or Vertical (Rod or Cable) Exit Device with functional lever (996L-R/V) to act like a rigid lever (996L-NL-R/V) with key over ride follow these steps:
R...
The Falcon Monarch 718C and the 718NL trims can be used on the 25-C exit device.
The 718C trim is listed in the Price Book for the 25 series
The instructions attache...
This is not a recommended application as the electric strike does not have the same holding force as the XP98/99 rim exit device. Typically the XP device will withstand a higher force than electr...
There is not enough room for both options as the dogging mechanism in a standard cylinder dogging and the electronics for the EL or QEL options are both located at the end of the base plate.
For 9...
The Von Duprin 6111 electric strike would work with DOM 1790 device on medium style doors
Centerline of the 1790 device mounting screws are located 1 11/16" from face of stop. See d...
Device: Pushbar end caps, pushbar trim and center case cover.
Trim: Lever assembly, trim plate assembly (trim plate and bushing sleeve).Bronze Finish Comparison
There is not a fire rated version of the Von Duprin 33A/35A rim device.
Only the vertical rod devices (33/3527A-F, 33/3547A-F, 33/3548A-F) can be fire rated.
To convert the Von Duprin 9975NL(Night Latch or Storeroom) to 9975L (Classroom) exit function follow these steps (Note: the mortise lock is shipped as Night Latch from the factory):
Turn the NL ...
To convert the Von Duprin 9975L to 9975NL exit function follow these steps (Note: the mortise lock is shipped as Night Latch from the factory):
Turn the NL screw on 7500 mortise lock counter clo...
Position the 379L trim and attach with countersunk screw into the bottom stud of the trim.
Position the 55 Rim device and attach with the device mounting screw through the he...