Steelcraft uses a 7 gage hinge reinforcement for 4 1/2" and 5" butt hinges as standard on all frame series.
The hinge reinforcement size for either 4 1/2" or 5" hinges (standard or heavy duty hing...
Steelcraft follows the industry standards for hinge reinforcement and preparation for both door and frame. Unless otherwise specified all products prepared for butt hinges will have mounting holes ...
With split key construction keying there are two ways the construction insert is retained in the cylinder so that it won't fall out the back end of the plug, see Figure 1.
The&nb...
Ives does not offer a continuous hinge designed specifically for lead lined doors. Standard hinges may work if the hinge and mounting hardware do not penetrate the lead lining in the door.&nb...
When trying to program a CM lock, it may display an error code with a solid green light and 10 read flashes. This indicates the lock has already been programmed with computer software and manual pr...
In an effort to continue providing the highest quality products and align with market demand Ives has upgraded the mounting screws provided for the majority of 8000 and 9000 series pulls.The new an...
The Date Code and Closer Size are stamped in the backside of the closer body.
Closer Size:
If the number is "1", the closer is a 2031 or 5031.
If the number is "3", the closer is a 2...
Cutout depends on the size of 224 hinge. See 112HD/224HD-EPT template.
112HD/224HD continuous hinge
Center line of EPT to top of the door
83 inches
30 inches
85 inches
32 inc...
Butt hinges can be used on doors up to 4' wide and 200 pounds. There is no maximum door height, just need to add a hinge for every 30" or part there of over 7'.
Hinge backset is the dimension from the leading edge of the hinge to either the stop on the frame or to the stop face (push side) of the door.
For operating clearance, the hinge backset on the d...
A Double Egress frame is a double door frame prepared to receive two single-acting doors swinging in opposite directions (both doors are) the same hand. These openings are installed in cross corrid...
Steelcraft locates all butt hinges from the top of the door to the centerline of each hinge as standard practice:
Locating hinges to the center line of the hinge keeps all hinge locations the sa...
The location to the top of hinge will vary depending on hinge size used.
6'8" Frame with 1 1/2 pair of hinges (top to top):
For 4 1/2" hinges from the head to top of each hinge is 7 1/2", 37 7...
Since most wire transfer devices such as an EPT or electric hinges cannot provide large gauge wires, we take the small gauge wire into account when determining the overall wire size for the device....
When you want to periodically disable and block access to a certain room in a building or an entrance door, that’s when you would need to use a Lockout Cylinder. See full document.
Doors require special downsizing for continuous hinges. The amount of downsizing depends on the hinge specified (manufacturer and type) and the hinge application (Full Mortise versus Full Surface v...
An EPT can be used with a Cam Lift Hinge:
Maximum hinge lift dimension = 1/2".
The EPT must be installed correctly with the tube at the top on the door side and the tube at bottom on...
There are two parts that can be referred to as control pins for a 23-030 (FSIC core).C603-967 is the lower control pin that sits in the seventh hole of the FSIC plug. (part B in exploded view) ...
Consider the Soss hinge like a butt hinge to determine the size of overhead that is needed. For templating use the same mounting group as a 4" wide butt hinge and the appropriate door thickness.
It is not possible to key SFIC and standard cylinders including Schlage FSIC into the same system. A keyway name may be shared between the two key fami...