l series thumbturn timing

RELATED FAQS

Question
Answer
Beginning January 2, 2013 Schlage will offer the Latitude (LAT) and Longitude (LON) levers in the 629 and 630 stainless steel finishes.
Schlage has conversion kits to convert the classroom L/LV9070 to the classroom security L/LV9071 and the classroom holdback L/LV9076 to the classroom security holdback L/LV9077.  The...
Screw part number is L583-485.  Screw type: 8-32 UC-2A W/#6 Flat truss head Phillips recess, header point.
The standard L9000 lock can be ordered for thin doors (1 3/8") and the appropriate parts will be shipped.  The LV9000, L400, LM9000, Anti-Ligature, and N escutcheon trims a...
The Schlage L-Series mortise lock spindle and spring part number can be found in the Table 1.     Spindles and Springs   Part Number  Description  L283-060 Spindle and spring, 1...
The inside lever mounting plate part number is L283-031.
The Schlage L-Series uses a clover leaf cam with the exception of the L9060 outside cylinder which uses a straight cam. The cam part number will depend on the type of mortise cylinder, keyway (for ...
Inside knob and bushing: 09-402 plus design and finishOutside knob: 09-401 plus design and finish
Effective December 9, 2019, Schlage L Series mortise locks with a thumbturn will ship standard with our new ADA thumbturn. The new ADA thumbturn is slightly smaller than the existing design while s...
Typical installation by an experienced Schlage L lock installer on a door correctly prepped for the Schlage L-Series function could take 10 to 20 minutes.  Many outside variables can change the amo...
Raceway availability: Optional factory installed raceways are available in doors but are not available in frames. Preparation Info: Steelcraft installs a flexible 1/2" ID steel conduit through the...
Steelcraft does not supply door louvers (loose or installed) and will only provides a cutout in doors for specified louvers sizes.
Stamped louvers are no longer available from Steelcraft in any door series. Steelcraft discontinued this offering in 2008. Steelcraft will only provide a cutout only in doors for louvers.
A UL 20 minute fire rating is the maximum fire rating for a Full Glass (FG) door design. A14-Series door construction: Max fire rating is 20 minute. UL label only FG must use Over-Lapping Stee...
You can order an L lock with a lever on one side and knob on the other as long as it's still rose by rose, or escutcheon by escutcheon (must be same style escutcheon). EXCEPTIONS: Knob trim o...
Includes the SL1 lever on one side and the SK1 knob trim on the other side.
The L series armor fronts are only available with square corners.  
UL Listed for 3-hour fire door (except L9076 and L9077)
The 09-611 indicator stands off the door 0.39".
The pricebook suggests (for a 1-3/4" door) using a 1-3/8" cylinder when installing with an 09-611 occupancy indicator.
Supply wires - 24AWGRX wires - 20AWGLX wires - 20 AWG
Typically for a 1-3/4" door you would use a 1-1/4" cylinder.  Use the Table in the Pricebook for a reference:  
Reference the L-Series Service Manual to change lock functions or build up a case from parts.
This Step-by-Step guide is specifically designed for the functions listed below, however, it can be referenced with a majority of L series functions since most of the parts are ...
RX wiring on all L9000 locks with RX switch manufactured after January 2, 2017:The L-Series switched to a handed modular three-wire request to exit (RX) switch. This change was originally completed...
Specific to the RX switch installed into the L9080EL/EU and L9082EL/EU and L9000 mechanical locks prior to January 2, 2017:ALL PART NUMBERS BELOW DISCONTINUEDThe L-Series switched to a three-wire r...
The ND-Series RX,  the L-Series RX and latch monitoring switches are Form C - Single Pole Double Throw (also known as SPDT).
Lockcase dimensions (depth x height x width) are: L/LV9000 -  4 7/16" x 6 1/16" x 1" L400 -  4 7/16" x 3 5/8" x 1"
 Mounting Posts   Part Number  Door Thickness  L583-211  1 3/8"  L583-212  1 3/4" - See note section on SL1 trim  L583-213  2...
To convert a Schlage mortise L9080 function to a L9070 function purchase and replace the following:   L283-133, L9070 lock case  L283-040, spring cage (for outside lever)