The standard screw pack for an LCN closer is the SRT (Self Reaming and Tapping) screw. Thru bolts are an option, but must be specified on the order. There is no charge for them, but they do need to...
Order the M204-198 thru-bolt jig, see Figure 1.
Figure 1: M204-198 thru bolt jig
The 40-080 was the old Schlage jig. The 030736-000-70 was the old Falcon jig. When the jig changed to...
An error - E04 - is an indication of a constant activation input from either the "Hold Open" switch or a "Wall Activation" switch when the 4600 power is turned on. This condition also occurs when l...
The old 4030/4130 closers and arms are obsolete, there is nothing to replace them. No arm from other closers will fit
There is no closer that can replace the old 4030 series closer with the exa...
An LCN 4040T with a reveal deeper than 1/8" on the pull side of the opening requires a Double Egress (DE)arm.
ST3073 Standard 4040T DE Arm will accommodate reveals up to 2-11/16"....
The Fusible Link arm is available with the 4010, 4020 and 4110 series closers. They all use the same Fusible Link arm. The UL Listing number is for the Fusible Link arms is R1943.
The 4010 Serie...
If using the LCN pneumatic control box as the air source for the Von Duprin Pneumatic devises then you have to use the LCN 925 tubing because of the size of air line fitting on the LCN co...
How to: What are the steps to adjust a door closer?Facts: All LCN and FALCON door closers will have 3 regulating valves and a spring adjustment. All closers with a "Delay" feature ...
The hold open position on a "REG" or "EDA" hold open arm is set with the door to a few degrees shy of the desired hold open point. To properly set, open the door 5° less then the desired hold open...
The part number for the solenoid air valve in the 7900 Series control boxes are:
7901/ES7901 - part# 941 - marked A
7902(S)/ES7902(S) - part# 942 - (2 valves) marked A and B
7949/ES7949 - part...
STANDARD ROD AND SHOE: 4020, 4031, 1460, 1520, 1370, 1070, 1260, 4640, 4820 is: 8 3/8”
LONG ROD AND SHOE: 4020: 4031, 1460, 1520, 1370, 1070, 1260, 4640, 4820 is: 12 3/8”
STANDARD ROD AN...
All Senior Swing models are heavy duty operators and have the Push-N-Go (PNG) feature. This feature is a programmable function in the control module.
The PNG settings are: Off, On, or FD (fixed)...
The 4640 Regular arm (4640-3077) is the same as:
4040 Long Arm
4820 Regular arm.
The arms listed above are for reveals up to 4 1/2" and have a 8 3/8" long rod and shoe.
4640 Long arm ...
The part number for the 1460 cylinder mounting bracket is: 1460-30A.At the end of August 2016, this mounting bracket is packed in the closer Screw Pack. Please note it used to be shipped loos...
Make sure that the hold open nut is not on upside down. The orientation of the hold open nut depends on the mounting.
On a Top Jamb "Push Side" mount, the hold open nut would poi...
Wiring and Riser diagrams can be accessed at:
Common wiring diagrams can be accessed at:
us.allegion.com
Go to "Document Library" > then choose Document type of "Wiring ...
The 4600 Series operator does not have a Push N Go feature.
The LCN operators with a Push N Go feature are the Senior Swing, Benchmark, and the Falcon 8200 series.