ma lock case

RELATED FAQS

Question
Answer
To remove the M lock trim follow the steps below in reverse.       The M lock spanner wrench is 021415.  Although this wrench is no longer available from&n...
Schlage now offers modular style cams to operate the Falcon MA locks.  The following part numbers are cams for all MA locks (except the MA381): L583-638 for 1-1/8", 1-3/8", 1-5/8" length cylin...
Price Book 72A List Price $8.10
The Schlage 09-509 rose style thumbturns will work but the spindle sits 90 degrees off from each other (Schlage is square, Falcon is diamond).  The result is the throw will end up 10 and 2 o'c...
The MA lock can be specified in a 12 or 24V DC configuration (default is 12V). Additionally, an AC power source may be used as long as a rectifier is installed in the circuit (not provided). He...
For additional details and a wiring diagram see the MA service manual page on electrical requirements here.
The MA lock is field reversible.  The process involves three potential steps depending on what hand is needed. Rotating latchbolt - Changes swing of lock.  ex (RH to RHR) or insw...
No parts are compatible between the Falcon MA-Series and the obsolete Falcon M-Series.
Solenoid: Black (2 wires) RX (monitors both sides) Normally Open: Green (pin 6 when connector included) Common: Orange (pin 5 when connector included) The current version o...
The Von Duprin 6210 electric strike was designed for retrofit applications and will not work with the Falcon MA series lock when strike and lock body are mounted at standard locations (centerline o...
The Falcon MA will not fit a 1-3/8" thick door. 
The lock case can be re-handed, however, this requires opening up the lock case. See M lock re-handing instructions for a complete guide.
Depending on the door construction the minimum stile may differ but a safe dimension would be 4-3/4".  CUSTOMER must check door construction. The pocket depth requirements of the case is 4 1/2".
The following templates are for the MA lock.  Use the matrix in each template for the specific function.  See here for Sectional trim . See here for Escutcheon trim. 
Falcon began offering an RX switch with its electrified functions beginning January 17th 2012.  To specify, add "RX" to the end of the part number. Example:  Storeroom Function...
The MA RX features a single switch within the chassis that will monitor both the inside and outside knob/lever.  The switch is only available as Normally Open (NO).
See Falcon MA lever assembly below: The spring mechanism (E) returns the lever to horizontal.  The parts are not sold separate, so if the lever sags, the entire lever assembly shoul...
Lever assemblies part numbers are found in the Pricebook.  Note they are handed.
See below for commonly requested dimensions on the MA lock.  Dimensions not found in other literature have a square around them. CL refers to "Centerline".  
Here are some of the major differences between the M and MA-Series.  Lever mounting post holes -  Locations have changed on door template.  (12 and 6 o'clock for M lock, MA lock is approx 1 and...
Falcon does not offer an "ADA style thumbturn.
The MA was launched 4/1/10 and replaced the Falcon M lock.
The MA lock does not have Vandlgard or a breakaway trim feature, however, the lever spindle on the MA lock will shear if too much force is applied in order to prevent internal lock damage and resis...
These dimensions and other general lock case dimensions can be found on template L1.  
Reference the L-Series Service Manual to change lock functions or build up a case from parts.
This Step-by-Step guide is specifically designed for the functions listed below, however, it can be referenced with a majority of L series functions since most of the parts are ...
The L9080 lockcase part number is L283-134.
Grade 1 mortise lock
Lock Case