minimum Stile sizes

RELATED FAQS

Question
Answer
The minimum stile for each lock will depend on the backset and the rose diameter/escutcheon width.  See the Schlage Minimum Stile Requirements for the minimum stile for eac...
Depending on the door construction the minimum stile may differ but a safe dimension would be 4-3/4".  CUSTOMER must check door construction. The pocket depth requirements of the case is 4 1/2".
For most exit devices, please refer to the specific device series catalog for minimum door opening width the device can be cut down to fit.   Be aware that some device options, frame...
The minimum recommended Stile measurement is 5” to allow proper mounting of the AD and CO series locks.
Minimum dimensions to cutouts for glass lights: Vertical edge of door to edge of cutout = 5 29/32" Top of door to top of cutout = 6" Bottom of door to bottom of cutout = 10" Reinforcing chann...
The minimum stile and rail dimensions with glass trim are as follow: Top Rail: 6 1/4" top of door to exposed glass or 5 1/2" top of door to cutout Center Rail: 6 1/2" exposed gla...
The minimum stile and rail dimensions are to exposed glass are: Stiles = 6 13/16" Top Rails = 6 3/4" Center Rails = 7 1/2" Bottom Rail = 10 3/4" For high traffic and high abuse locations th...
55 and 88 are both crossbar exit devices.  55 Series is used on narrow stile applications, 88 is for wider stile applications. See attached tables for 55 and 88 series minimum stile requirement...
Minimum stile depends on several factors.  The information will be on the specific template for your door and hardware.Start by opening the templates page.Click here -->:  98/99 T...
LCN recommends an 18 AWG (minimum) wire size (gauge) to the 8310 Series hardwired actuators.
The minimum rose that can be used on the 61L (ANSI/BHMA A156.115.18) preparation is 3 7/16". Steelcraft's 61L lock prep (often referred to as the "Squashed Turtle lock prep") is designed for Bored...
Yes, glass light can be used or prepped in conjunction with the Von Duprin 94/95 Series INPACT device however there are dimensional limitations between the glass light and the InPact door preparati...
Glass lights available: Standard Glass Lights - The N4, N5 & V lite can be used at standard locations with out any modification. Glass Light Options - Other glass lights are available but ...
The 2010 and 2030 closer are not the same. The 2010 Series closer uses the (larger) 4010 cylinder which requires a 4" minimum frame tube to mount in. The 2030 uses the (narrow) "Pacer" cylinder...
Maximum Dutch Door sizes are: Non Labeled = 4'0" wide X 8'0" High Labeled = 4'0" wide X 7'2" High Special sized Dutch Doors are available: Special size top and/or bottom leaves are availabl...
 DESCRIPTION PART NUMBER   Conventional Core  23-030  Conventional Core less logo  23-031  Primus Core  20-740  Primus XP Core  20-740-XP  Primus Core less logo  20-741 ...
The Schlage L9000-Series with anti-ligature trim cannot be ordered less cylinder (L cylinder suffix), but can be ordered less core (BD or J cylinder suffix). The cylinder rose dimensions change bas...
The following size limitations per frame unit, are in enforced for welded elevation frames shipped from the factory. These limitations are in place due to the physical size of shipping tr...
Lock Edge, Strike Edge
Hinge Rail
Rail
Vertical Door Edge; rail
See below for commonly requested dimensions on the MA lock.  Dimensions not found in other literature have a square around them. CL refers to "Centerline".  
Yes.  A fire rating was approved in 2016.Please see the 33A/35A catalog here for more information:http://us.allegion.com/content/dam/allegion-us-2/web-documents-2/Catalog/Von_Duprin_33A.35A_Se...
Von Duprin will not supply the 8827-F less the bottom rod because the device has never been UL tested less bottom rod.