rim cylinder prep schlage fsic

RELATED FAQS

Question
Answer
The Schlage SFIC rim cylinder driver is part number B520-365, shown below.     Figure 1: SFIC Rim Cylinder Housing
Standard Schlage rim cylinders will fit a total thickness of door and projecting trim of 3 inches, this includes a minimum of 3/8" of engagement of the tailpiece into the exit device.  See ima...
For total thickness measurements larger than 3 inches see the special cylinder offerings in Pricebook.  Specify the part number and include the total thickness.  We do not offer the ...
Only the Schlage ND-Series can be prepped to accept non-Schlage cores. All designs are supplied with the appropriate tailpiece Non-Schlage cores are NOT included Lever designs available vary d...
 The tailpiece of the rim cylinder can be inserted into the Von Duprin 98/99 rim device either vertical or horizontal.
Yes, the Falcon Doromatic 2090 EO is ready to accept an exterior rim cylinder for key entry or hold back if desired.
2021 Update: An updated version of this knowledge entry can be found by clicking HERE.       Part numbers for Schlage and Falcon cylinders for Von Duprin device...
  FALCON   Mortise Rim KIL Conventio...
    If unclear whether mortise, rim, or key-in-lever is needed, reference links below to determine what cylinder type is needed.   In order to determine cylinder type n...
The following list of cylinders were not affected by the change to modular cylinder:    09-900, 09-904, 09-905, 09-907 mortise cylinder turnsSmall format interchangeab...
For night latch function with pull by others, the 98/99 series mortise exit device should be ordered as NL less trim, e.g., 9875NL-L/TRIM.  We will furnish a device only, and the mortise cyl...
Von Duprin offers two options:   The CDSI/HDSI Dogging Indicator provides an at-a-glance verification of the status of the door from inside of the room. Visible “LOCKED” and “UNLO...
The Von Duprin 98/9975 -2 device requires a RIM cylinder on the exit device side of the door and the outside trim requires a 1 1/4" mortise cylinder with straight cam. 
Inside cylinder locks and unlocks the outside trim, such as thumb piece, knob or lever.  Outside cylinder functions as an NL when inside cylinder locks the outside trim.Double cylinder fe...
A modular cylinder's length is determined by 4 basic parts; a cam screw, cam, plug extension, and a back housing.  Most of these parts are used in more than one cylinder length and...
The current 812L trim will replace the older 182L trim. Due to the thicker escutcheon plate of the 812L trim a 1 1/2" mortise cylinder with straight cam for mortise devices or a longer rim cylinde...
Both cylinders are standard non-ic rim cylinder. 20-022 has a horizontal tailpiece 20-021 has a vertical tailpiece
Modular cylinder was launched July 26, 2010 and replaced the standard key-in-lever, mortise, and rim cylinders.     For a list of cylinders not affected by the modular cylinder design change cli...
This product was available until 2001 when it was discontinued. Part Number Description XB09-728 Entrapment mortise cylinder, P keyway XB09-834 Entrapment rim cylinder, P keyway ...
You will need a 1790NL/HB cylinder assembly (part number CYLASY.1151) and a rim cylinder.
There are different mortise cylinder length options depending on the cylinder type. Below is a list of available options for conventional, FSIC, and SFIC cylinders, as well as the convent...
It is not possible to key SFIC and standard cylinders including Schlage FSIC into the same system.  A keyway name may be shared between the two key fami...
The Schlage B and BD cylinder suffixes designate less small format interchangeable core (SFIC) cylinder prep for the lock. Any SFIC, 6-pin or 7-pin, can be inserted into the lock and will operate t...
The new AL FSIC driver part number is A700-052.  This driver snaps onto the back of the core similar to the ND, as opposed to it being assembled into the lock chassis with a retaining ring.  Th...
The RU lock can accept a Schlage Full Size core, but the cylinder suffix must be specified as "J IC-SC" so the correct parts are supplied. The tailpiece will come with the lock. Example: RU581J IC-SC
Schlage offers a face plate adapter to adapt 1" face plate to 1 1/8" door preparation, part number is A501-878.
Refer to Table 1 for a list of T lock tailpieces for conventional cylinders.  Table 2 shows IC tailpieces. Table 1: T lock conventional tailpieces Table 2: T lock IC tailpieces
The center to center distance is 4 inches.
These items are not available from Schlage or Falcon. There are third party companies such as Don-Jo or Pro-Lok that manufacture cover plates.
The G-Series lockset was discontinued in 1981, and all service parts for the G-Series lock were discontinued in 1985. 
 The current interconnect lock, S200 series (available in levers only), will not fit into the same door preparation.
Schlage G Series template locate here.
All the templates can be found at us.allegion.com   Please click here
The T lock can accept a Schlage Full Size core, but the cylinder suffix must be specified as "J IC-SC" so the correct parts are supplied (including the tailpiece) Example: T581J IC-SC
There is not enough room for both options as the dogging mechanism in a standard cylinder dogging and the electronics for the EL or QEL options are both located at the end of the base plate. For 9...
The 1790EO does not ship with a cylinder assembly. If you wish to convert a 1790EO to NL or HB operation, then you will need the 179CA cylinder assembly and a standard rim cylinder.
This is possible: For metal doors prep door according to the 24R/V NL-OP Template or the 25R/V NL-OP Template and for wood doors use 24R/V NL-OP Wood Template or 25R/V...
Double cylinders are only available on Von Duprin 98/99 Rim and 98/9975 Mortise devices.
You would have to order the device as 88NL less trim, the device will be shipped as an 88EO.  The EO device has an NL cam to accept a rim cylinder tailpiece. 
Rim cylinder housing only for FSIC is part number 20-079.
Rim cylinder housing only for SFIC is part number 80-129.
There are two types of interchangeable cores: Full size interchangeable cores (FSIC) Also known as Large Format Interchangeable Cored (LFIC) Each manufactures FSIC c...
The Schlage small format interchangeable core rim cylinders 80-329, 80-159, 80-116, and 08-129 can accept 6 pin and 7 pin small format cores.
The Schlage rim cylinder lengths are given below and were measured from the face of the cylinder to the back of the tailpiece.  Because of allowable tolerances for each part the average length is l...
B502-899 is the tailpiece for both the SFIC and standard rim cylinders.
The rim cylinder with thumbturn, XB11-979 (Figure 1) was designed to be installed on the inside head of the Von Duprin 98/99–2 double cylinder exit devices, see Figure 1. The rim cylinder with...
To add a cylinder to the 98/99-EO rim device order a 110NL-MD for metal door or 110NL-WD for wood door with a standard rim cylinder and prep the door per template.
The B220-001 is an FSIC rim tailpiece and driver.
A 1-1/8 through 1-1/2" mortise cylinder with straight cam per Step 4 of 512NL Instructions.
The 2670 Guard X uses a standard rim cylinder for either push side or pull side.  The rim cylinder can be installed to the outside of the opening with an offset pull to operate the 2670 Guard X d...
See descriptions for the 09-992 thru 09-997 parts kits for modular mortise cylinders.  The 09-998 is a kit for a rim cylinder.      
The 98/99 rim device can be converted to double cylinder 98-2 or 99-2. Double cylinder features an inside key cylinder which locks or unlocks the outside trim (Classroom Function) and an outside...
The 98/99 rim device can be converted to double cylinder 98-2 or 99-2. Double cylinder features an inside key cylinder which locks or unlocks the outside trim (Classroom Function) and an outside c...
Order the device as 88 NL less trim. The cylinder will be mounted to the face of the door. Use templates 10156 and 40015.
SD is Special cylinder dogging in the center case of 98/99 rim and vertical rod non fire rated devices and is available with standard, EL, QEL, CX and ALK.