WHAT DOES RD SUFFIX MEAN ON SCHLAGE LOCK?

RELATED FAQS

Question
Answer
The L9466 Store/Utility Room lock can provide this functionality. Operation: Latchbolt retracted by knob/lever either side. Deadbolt thrown or retracted by key from either side. When the deadbolt ...
Please contact the Allegion Product Support Team on all questions or inquiries pertaining to hardware finishes warranties. Please send an e-mail to the applicable Product Support team:Closers_TechP...
The commercial Aged Bronze finish (643e) is the BHMA equivalent to a copper plated, blackened, relieved and then clear coated product. This commercial finish is identical to the residential Aged ...
On ND locks manufactured on or after January 30, 2017 only the SFIC lever and SFIC driver are needed to convert the lock from Full Size conventional (PD) or Full Size IC (JD, RD, TD) prep to S...
On ND locks manufactured prior to January 30, 2017, the lever, spring cage and tailpiece needed to be replaced with the SFIC lever, SFIC spring cage and the SFIC driver . N123-056 - Outside sp...
MultiPoint locks are three-point locking systems that secure the door at three points – top, bottom, and traditional center latch location. Operating just like traditional locks, MultiPoint locks...
The Schlage B and BD cylinder suffixes designate less small format interchangeable core (SFIC) cylinder prep for the lock. Any SFIC, 6-pin or 7-pin, can be inserted into the lock and will operate t...
A lock specified by a cylinder suffix BDC will be supplied with a disposable small format construction core, see Figure 1 below.  There is no metal key but instead the BDC cylinder has a ...
A small format disposable core is used as a SFIC construction core that is for low security applications and can be thrown in the waste bin after use.
The full size interchangeable cores or FSIC from Schlage.
The Schlage ND is shipped with a driver/tailpiece when ordered with a LD, BD, or JD suffix.
The T lock can accept a Schlage Full Size core, but the cylinder suffix must be specified as "J IC-SC" so the correct parts are supplied (including the tailpiece) Example: T581J IC-SC
The RU lock can accept a Schlage Full Size core, but the cylinder suffix must be specified as "J IC-SC" so the correct parts are supplied. The tailpiece will come with the lock. Example: RU581J IC-SC
Falcon D series deadbolts will not accept Schlage Key-in-lever cylinders. The faceplate plug hole is smaller in diameter than the Schlage plug and does not fit flush when i...
For a Schlage "C"  keyway:  Specify "CP6" as the cylinder suffix when ordering  D100 or D200 locks (All other Schlage keyways are not available).
Schlage changed to the Everest 29 default keyway on March 4th, 2013. At that time, Everest 29 S123 became the default keyway for all Schlage locks. Everest product is still available but must be sp...
Schlage and Falcon use the P cylinder suffix to designate conventional key-in-lever (KIL) 6 pin cylinder.  The D means that the lock will have a deadlatch.
The Schlage L9000-Series with anti-ligature trim cannot be ordered less cylinder (L cylinder suffix), but can be ordered less core (BD or J cylinder suffix). The cylinder rose dimensions change bas...
Grade 2 locks are tested and certified to be in compliance with the following ANSI/BHMA Standards: Cylindrical, Bored and Preassembled Locks & Latches 400,000 Certified Cycles ANSI...
Schlage has several options shown below.
Grade 1 locks are tested and certified to be in compliance with the following ANSI/BHMA Standards:   Cylindrical, Bored and Preassembled Locks & Latches   8...
While they are both mortise locks they are not interchangeable.  You would NOT be able to use a L9000 with a VD panic device. You would NOT be able to use a VD 7500 with Schlage lev...
Von Duprin offers two options:   The CDSI/HDSI Dogging Indicator provides an at-a-glance verification of the status of the door from inside of the room. Visible “LOCKED” and “UNLO...
The B series accepts 6 or 7 pin small format cores when specifying with the "BD" cylinder suffix (less small format interchangeable core).  The tailpiece shown below is used for bo...
Specify the J cylinder suffix followed by IC-CR6 or IC-CR7 (6 or 7 pin Corbin core) Example: T581J IC-CR6  This will accommodate an 8000 or 8000-7 Corbin Russwin Full Size core.
The L9000 lock can be ordered for doors greater than 1 3/4" thick.  The allowable door thickness is dependent on the L lock function and how the lock is extended.  All locks for exte...
Use the cylinder suffix 'T' for full size interchangeable core or the cylinder suffix 'HD' for small format interchangeable core, see Figure 1.  Small format also has a disposable core option ...
The Falcon MA mortise lock is available with an occupancy indicator on the following functions: MA301, MA311, MA321, MA371, MA431, MA441(inside of door only), MA451, MA541, MA57...
Related solution: Is the MA indicator available separately? 
Finish is not specifically stated as being covered under warranty as it is covered under defects in material and workmanship.  EXCEPTION: There is no finish warranty for Falcon products. ...
Falcon lock warranty statementIves warranty statementGlynn-Johnson warranty statementLCN closer warranty statementSchlage warranty statementSteelcraft warranty statementVon Duprin warranty statement
  There are several Schlage and/or Falcon locks that have been tested and approved for this application. For Commercial use the locks have been tested and approved as ...
1) General Lock was purchased by Schlage - 1973 2) General Lock moved to Security and turned into the K-lock - 1977 3) K-Lock discontinued - approximately 1984 4) L-lock introduced - approxim...
The minimum stile for each lock will depend on the backset and the rose diameter/escutcheon width.  See the Schlage Minimum Stile Requirements for the minimum stile for eac...
SCHLAGE locks are available with the following backsets: Lock Series Lock Type                 ...