The current 812L trim will replace the older 182L trim.
Due to the thicker escutcheon plate of the 812L trim a 1 1/2" mortise cylinder with straight cam for mortise devices or a longer rim cylinde...
A modular cylinder's length is determined by 4 basic parts; a cam screw, cam, plug extension, and a back housing. Most of these parts are used in more than one cylinder length and...
There have been a few reported cases of the torx cam screw loosening on modular designs shipped prior to April 16th 2013.
History of cam screw changes:
Standard screw shipped July 27t...
You would have to order the device as 88NL less trim, the device will be shipped as an 88EO. The EO device has an NL cam to accept a rim cylinder tailpiece.
The Von Duprin CD kit comes with the cover plate machined to accept the cylinder dogging mortise cylinder.1 1/4" mortise cylinder with an inverted straight cam is required for CD option on Von Dupr...
The Schlage L-Series uses a clover leaf cam with the exception of the L9060 outside cylinder which uses a straight cam. The cam part number will depend on the type of mortise cylinder, keyway (for ...
4754, 4854 and the 9854 are electrified mullions and handed as noted below:
4754 is not handed:
Prepared for two 4263 monitor strikes.
Use with all Von Duprin rim panic devices
4854 is han...
Chexit devices shipped after 8-24-2015 with motor driven:
The Chexit device will use a 1 1/4" mortise cylinder with straight cam. Schlage cylinder 20-001-114 recommended.
CAUTION: The length of t...
Chexit devices shipped prior to 8-24-2015:The CX device will need a 1 1/4" mortise cylinder with a straight cam per page 2 of the installation instructions. A 996L-M for a 1 3/4...
Von Duprin KR (key removable) mullions requires a 1-1/8" or 1-1/4" mortise cylinder with the standard straight cam, the cam is not inverted. Please see chart below for part numbers.
Warranty Statement3 Year Limited Mechanical Warranty and
1-Year Limited Electromechanical Warranty - Additional warranties listed below
The provisions of these limited warranties do not apply
to P...
The B520-698 cam was designed for a Schlage IC mortise cylinder (see Figure 1) to operate a Falcon MA lock, all functions except the MA381. There is no Schlage cylinder option ...
L583-446; Schlage Adams Rite MS modular cam used on 1 1/8", 1 3/8" and 1 5/8" cylinders
L583-447; Schlage Adams Rite MS modular cam used on 1 1/4", 1 1/2" and 1 3/4" cylinders
B502-944; Sch...
Devices built After 2/28/2011: Use a 1 1/8" - 1 1/4" mortise cylinder with straight narrow cam. (Cam profile same as the Schlage B520-731, see table below for part numbers)
Devices built Befo...
Modular 1-1/8"
Modular 1-1/4"
SFIC and FSIC
Non-Modular Non-IC Conventional
Non-Modular Non-IC Everest Primus
B520-730
B520-731
B520-2...
The Sargent cams listed below work for all applications except 16 inside and 50 outside. The equivalent Sargent cam is the 13-0660.
Use the B520-736 for modular cylinder lengths of 1 1/8",...
Unless otherwise specified on an order, the cam supplied on Falcon mortise cylinders will be the following:
Non-IC mortise cylinder is the 5622-STD.
IC mortise cylinder is the 5622-IC.
Related...
Cams for other applications may be specified with no additional charge, see pricebook.
Effective July, 2014, there is no longer a specific modular cam part number for dogging. The Schlage modular straight cams come with two mouting holes that allow for the cams to be mounted inverted...
1 1/8" mortise cylinders fit the 650 series keyswitch.
The 650 series keyswitch when ordered with the cylinder, will come complete with the correct cylinder, cam, and any required blocki...
If blocking rings (PN 36-079) are needed, specify dimensions when ordering. See below for blocking ring (PN 36-079) dimensions.
Blocking Ring
Specify Dimension
1//8"
...
Installers have reported that their AD-CO Series cylindrical or mortise locks will unlock whenever the outside lever is lifted.
This will occur if the outside spindle (square post) is install...