Medeco does offer a key-in-lever cylinder to fit the Schlage ND.
You will need to contact Medeco for the cylinder
Specify a key-in-lever cylinder to fit the Schlage ND lo...
The JD YA6 tailpiece is intentionally designed such that the tailpiece cannot be installed at the same time as the cylinder.
Interchangeable cylinders assume that the lever and taipiece is i...
Standard Schlage cylinders will not fit in Yale locks, but Schlage does offer special retrofit cylinder that, when ordered, can fit into specific Yale locks. See below for retrofit options.
...
The indicator on a cylindrical hotel lock is a small pin that projects outward from the face of the cylinder plug (Figure 1) when the inside push button is depressed. When this pin is ...
The minimum stile for each lock will depend on the backset and the rose diameter/escutcheon width. See the Schlage Minimum Stile Requirements for the minimum stile for eac...
The S-Series and S200-Series outside keyed spindle was redesigned in September 2008.
For locks manufactured BEFORE September 2008
The S and S200 lever cylinders required cy...
The standard door range for an AL lock is 1 3/8" to 1 7/8". Using the supplied instruction sheet, align the springcage post to desired door thickness by adjusting the outside castle nut.
See inst...
Key in lever
Falcon cylinders do not work in Schlage locks. The cylinders may fit, but there are no specific tailpieces created to operate any Schlage lock.
SFIC
SFIC is universal so Falcon and...
Hotel cylinder in L9000
As long as the correct cam is used (Schlage clover), a Falcon Hotel cylinder will properly function in an L9486 hotel lock.
Only the Schlage ND-Series can be prepped to accept non-Schlage cores.
All designs are supplied with the appropriate tailpiece
Non-Schlage cores are NOT included
Lever designs available vary d...
The Falcon Monarch 510L and 510L-NL trim will accept either a 1 1/4" Mortise cylinder with a straight cam or a 1 3/8" Mortise cylinder with a straight cam using the blocking ring provided with the ...
The Sargent cams listed below work for all applications except 16 inside and 50 outside. The equivalent Sargent cam is the 13-0660.
Use the B520-736 for modular cylinder lengths of 1 1/8",...
The RU lock can accept a Schlage Full Size core, but the cylinder suffix must be specified as "J IC-SC" so the correct parts are supplied. The tailpiece will come with the lock.
Example: RU581J IC-SC
Refer to table 1 for the list of Schlage AL-Series cylinders.
AL-Series Cylinder Reference Table
Function
Cylinder Mechanism
Complete Cylinder
Non-Hotel Functions
...
The T lock can accept a Schlage Full Size core, but the cylinder suffix must be specified as "J IC-SC" so the correct parts are supplied (including the tailpiece)
Example: T581J IC-SC
The new AL FSIC driver part number is A700-052.
This driver snaps onto the back of the core similar to the ND, as opposed to it being assembled into the lock chassis with a retaining ring.
Th...
Specify the J cylinder suffix followed by IC-CR6 or IC-CR7 (6 or 7 pin Corbin core)
Example: T581J IC-CR6
This will accommodate an 8000 or 8000-7 Corbin Russwin Full Size core.
The easiest method to obtain an AL lock for a 2" door is to specify a 2" thick door when ordering.
Part required by function:2 each A700-043 driver & A700-034** lever insert in addition to the chassis parts below:AL10S – 2 hubs A700-028AL25D – 2 hubs 1 A700-028 (inside), 1 A700-030 (outside)...
Schlage offers Falcon Retrofit cylinders to fit many of Falcon's locks. Table 1 below contains part number for T series locks.
Table 1 - Falcon retrofit cylinders