Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ XP device template ”

RELATED FAQS

Question
Answer
What electric strike can be used with the XP98/99 devices?
This application is not recommended as elelctric strikes have never been tested with XP98/99 exit device because it would defeat the XP device holding force purpose.   The holding force f...
Is the Von Duprin 6111 electric strike compatible with Von Duprin XP98/99 rim exit device?
This is not a recommended application as the electric strike does not have the same holding force as the XP98/99 rim exit device. The electric strike has 1500 pounds of holding force whereas the XP...
What mullions should be used with XP devices?
The Von Duprin XP98/99 device uses a different strike than standard 98/99 device. The 909 strike is for non fire rated XP devices and the 954 strike is for the fire rated XP device. 49/9954 mul...
Is the Von Duprin EL option available on Von Duprin XP98 or XP99 exit devices?
The EL (Electrified) option is available with Von Duprin XP98/99 exit devices. To order, specify ELXP98/99 with proper trim.
Does the Von Duprin 6121 electric strike work with the Von Duprin XP exit device?
Von Duprin does not recommend using XP98/99 devices with any electric strike.   Von Duprin recommends using the standard 98/99 rim device.  The XP device has 2000 pound holding forc...
How does the latch bolt retract on the Von Duprin XP device?
The latch bolt on an XP98/99 exit device does not retract. The latch bolt will release and pivot out of the way when push bar is depressed or out side trim is activated.
Which strike do you use with an XP98/99 device?
The 909 strike is used in single and paired non-fire rated and single fire rated openings.  The 954 strike is used in fire rated paired openings.
The 1609 strike cannot be used with Von Duprin XP98/99 exit device.
Where can I find templates for the 237L two point latch device?
Attach is the instruction and template for 237L device, 237 Instructions.
Is there a template that shows where to drill the hole for E/EL/SS/RX/LX/CX wires?
The hole should be drilled in the field once the end cap is located on the door.  It is a 5/8" hole, that is located 5/16" from the end of the mechanism case. See installation instruction of t...
What is the difference between Von Duprin 98/9947 and 98/9948 concealed vertical rod devices?
There are two main differences:The bottom latches are differentThe Von Duprin 98/9947 concealed vertical rod device covers up to 1/4" undercutThe Von Duprin 98/9948 concealed vertical rod device co...
They both use Template # 10320_c
Can a 24-R or 25-R series device use just a cylinder on the pull side for NLOP function?
This is possible: For metal doors prep door according to the 24R/V NL-OP Template or the 25R/V NL-OP Template and for wood doors use 24R/V NL-OP Wood Template or 25R/V...
Needs template for the 55L X 379L. Where is that located on line?
What is the SUS feature "Device Template"
 See the attached Technical Note for instructions on saving a "Device Template" FROM a device or loading TO a device, Device Template Tech NoteOn the SUS/HHD go to the LOCK Properties tab, and sele...
Where is the template for the 718 trims made after 2/28/2011 for Falcon/Monarch concealed vertical rod devices?
See the installation instructions 718 for -C devices.
Templates for current 718 series trim can also be found on Falcon website
What templates do I use for the RX98L x E996L?
 Click Here to view the Hollow Metal or Wood Door Templates for Von Duprin devices   The E996L trim and RX98/99 devices  use the standard 996L and 98/99 templa...
Can a magnet, or sentronic device, be released and close the door from a button at a desk?
If a door is being held open by the LCN SEM 7800/1900 magnet or any ME/SE Series Sentronic LCN closer, you can remotely release that door to close by ordering the following parts and wiring per ST ...
On which closer is the fusible link arm available?
The Fusible Link arm is available with the 4010, 4020 and 4110 series closers. They all use the same Fusible Link arm. The UL Listing number is for the Fusible Link arms is R1943. The 4010 Serie...
Can I mount an LCN Cush closer with an GJ overhead stop?
It would be unnecessary to use the CNS/Cush arm and the Glynn Johnson overhead devices in the same application, both mechanisms stop the door.
Is there a wood door template for the 9957?
There is not a wood template for 9957 three point latches, use the 98/99 rim template W10301 to get the correct device backset.  For NL trim (990NL) use trim template and installation instruction W...
Where is the template for the 25C NL-OP?
The NL-OP function for 25-C uses the 718C trim, so template T-2211 for metal doors and W-2211 for wood doors for 718 trims prior to 2/28/2011. T-2211 for trims prior to 2/28/2011 W-2211 for...
STRIKE TEMPLATE MACHINE SCREWS
STMS