User questions

Question
Answer
  • What is the warranty for Schlage commercial mechanical locks?
  • Is there a latch spacer or reinforcement for the ND lock?
  • What type of switch is used for the RX and latch monitoring options for the ND and L locks?
  • What backsets are available on Schlage and Falcon locks?
  • What is the part number for the ND solenoid?
  • What are the part numbers for the SFIC driver and spacer used on the ND series locks?
  • What is the warranty for Schlage commercial mechanical locks?
  • What type of switch is used for the RX and latch monitoring options for the ND and L locks?
  • Is there a latch spacer or reinforcement for the ND lock?
  • What backsets are available on Schlage and Falcon locks?
  • Why is the ND lever hard to push on?
  • How do you order the ND series lock with a small format core?
  • Which closer should I use for a "High Wind" condition?
  • What are Hold Open Closers & Magnets?
  • How do I set the hold open on my 4040 closer?
  • What is a 62A shoe used for?
  • What is SRI?
  • Can you order a 1461 cylinder only?
  • What special template (ST) is used with the 2030 closer and a low profile track and roller?
  • Can you manually pull a 4040SE out of hold open?
  • Can a 4010 be mounted with swing clear hinges?
  • In what direction should the hold open nut be pointing for a 4041 H closer, up or down?
  • What are the dimensions of the SC70 footprint
  • Can the 4630/4640 cylinder only be replaced?
  • Does LCN still make a closer that has the built in smoke detector?
  • Is there a retrofit closer available for the obsolete 303 OHC closer?
  • What is the delay time adjustment on a Delayed Action closers?
  • What is the narrowest door a 4040 pull side will mount on?
  • What are the Rod and Shoe lengths for 4000 and 1000 series closers?
  • Is there adjustment limits on the regulation valves of LCN manual closers?
  • Does LCN sell a coupler to stack two 4040XP closers together?
  • What is the maximum degree of opening you can template a 4110 Cush closer?
  • Will the MPB-842 or MPB-840 power EL or QEL devices?
  • What power supply do I need for my 2 QELA devices with LCN auto operator?
  • How many Von Duprin QEL devices can be connected to a power supply?
  • Will the Von Duprin PS902 power supply operate the QEL device?
  • Does the QEL retract the latch bolt and the pushpad?
  • Can I run 4 QEL devices from one PS902?
  • What power supply do I use with an L9000 electrified L lock?
  • Will the PS861 power an EL99?
  • What is the power output of a 4600 operator?
  • What are door levels and models?
  • Does Steelcraft offer textured steel face sheets on doors?
  • Can protective plates be attached to fire rated door?
  • What are the wire gauge and length requirements for QEL devices?
  • Is the SD option available with Von Duprin QEL 98/99 exit devices?
  • How much amperage does the QEL draw?
  • Will the PS900-2 RS operate the Von Duprin QEL device?
  • Why is my QEL device not retracting completely?
  • What is needed to keep the EL device retracted all day?
  • How far down can an exit device be cut down in the field?
  • How are Butt Hinges located?
  • Lead times, Freight policies and guidelines?
  • How do I contact Allegion Customer Service or Technical Support?
  • What is the part number for the 88 series dogging screw?
  • Does the door prep need to be altered when ordering the L9000 locks lead lined?
  • Is lead lining a GJ overhead an option or even needed when used in an X-ray room?
  • How are Butt Hinges located?
  • Lead times, Freight policies and guidelines?
  • How do I contact Allegion Customer Service or Technical Support?
  • What is the part number for the 88 series dogging screw?
  • Does the door prep need to be altered when ordering the L9000 locks lead lined?
  • Is lead lining a GJ overhead an option or even needed when used in an X-ray room?
  • What is the maximum door thickness a rim cylinder can fit on?
  • What cylinder is required for the 360L from Von Duprin?
  • What cylinder is used for the Von Duprin -2 double cylinder function?
  • How do I order an 88 rim to accept NL cylinder and pull by others?
  • Can I add a cylinder function to the 98/99 Rim EO device?
  • Can you add double cylinder to an existing 99 rim device?